Graflex Speed Graphic
|Pre-Anniversary Speed Graphic; side view|
shows settings for focal-plane shutter
Note the solenoid on the lensboard.
image by Rick Soloway (Image rights)
The famous Graphic press cameras from Graflex were made in a number of variants and in several formats. "Speed" referred to the high shutter speeds available from the rear focal-plane shutter used in these models.
The earliest Speed Graphics were available in 3¼x4¼, 4x5 and 5x7 formats. By 1939-1940 the 5x7 format was dropped and the 2¼x 3¼ format was added. Focal plane shutters were available from the beginning until 1970. Models with a focal plane shutter can use lenses mounted in shutters or barrel lenses (without shutters). The Pacemaker Crown Graphic, introduced in 1947, was the first model available without a focal plane shutter, followed by the Century Graphic. Otherwise these share features with the Speed Graphic series.
- "Top Handle" Speed Graphic
- 1912-1927, 3x4, 3¼ x 5 1/2, 4x5 and 5x7. Focal plane shutter. Had very small lensboards so they are unable to use most later (large) lenses.
- "Pre-Anniversary” Speed Graphic
- 1928-1939, 4x5 and 5x7, (also 3¼ x4¼ from 1935 to 1939) Had larger lensboard. Focal plane shutter.
- "Miniature" Speed Graphic
- 1939-1946, 2¼ x 3¼. Used the Graphic (spring) back. There were Graflok back kits made that had a round depression with two contacts for the focal-plane-shutter flash-sync contacts where the peep sight usually folds down. Focal plane shutter.
- "Anniversary" Speed Graphic
- 1940-1946, 3x4, 4x5. Satin black with chrome trim except the wartime model had no chrome. Bed and body track rails were linked, allowing focusing of wide angle lenses within body. Solid wire frame viewfinder. Focal plane shutter.
|Pacemaker customized with|
massive Aero Ektar f2.5
image by Cory.Lum (Image rights)
- Pacemaker Speed Graphic
- 1947-1970, 2¼ x 3¼, 3x4, 4x5. Mahogany/metal body. Coated lenses, lenses in shutters, body release, folding infinity stops. Side mounted rangefinder replaced by top rangefinder on 4x5" Graphics in 1955. Most Pacemakers have the Graflok back. The Graflex back (usually found on the "Graflex" SLR cameras) was an option on some Pacemaker models. Newly designed focal plane shutter. The shutter table of the old cameras with 24 speeds was changed to 6 speeds in this camera. Focal plane shutter.
- Pacemaker Crown Graphic
- 1947-1973, 2¼ x 3¼, 3x4, 4x5. Same as the Pacemaker Speed Graphic but without the focal plane shutter, resulting in a thinner, lighter camera. No focal plane shutter.
- Century Graphic
- 1949-1970, 2¼ x 3¼ only. Plastic-body. Graflok back molded as part of body. No body-mount shutter release. early models had a flat bar viewfinder, followed later by models with a flexible wire viewfinder. No focal plane shutter.
- Super Graphic
- 1958-1973, 4x5. All metal body, flash computer, electric shutter release, front standard had swing capability, revolving back. No focal plane shutter.
- Super Speed Graphic
- 1961-1970, 4x5. Same as the Super Graphic but with faster shutter (speed to 1/1000) No focal plane shutter.
The Graphic back (also known as the "Spring Back") retains the focusing screen and hood assembly to the back of the camera using a pair of wide flat springs. This permits cut film holders to be inserted between the focusing screen and hood assembly and the camera body. When the cut film holder is inserted, it pushes the focusing screen assembly back slightly. The tension of the springs holds the film holder in place.
Because there is no mechanism (other than removing a pair of screws) to permit the focusing screen to be removed, roll film holders were made to slide in place and be retained by the focusing screen, just as with cut film holders. Some roll film holders were made with a "straight through" film path. These had the supply spool on one side and the take-up spool on the other. This meant that the partially-assembled roll holder was inserted into the back and then the take-up side was assembled from the opposite (left) side. This type of roll film holder could not be removed until the roll was finished. Roll film holders with a "u-turn" film path were made. This type had the supply and take-up speels on the same side of the camera. They ran the film path over a roller. If supplied with a dark slide, they could be removed mid-roll.
On the Anniversary model, the entire Graphic back assembly could be removed from the back of the camera for replacement with a Graflok back. Graflok backs were sold by Graflex for this purpose.
The cast-magnesium Graflok back was introduced in 1949. "Anniversary" and "Pacemaker" models that were made with Graphic backs could have Graflok backs installed. (These backs are attached to the cameras with just four screws.) Graflok backs were sold by Graflex for this purpose. All "Century" models had the Graflok back molded as part of the body. The "Super Graphic" and "Super Speed Graphic" models have rotating Graflok backs. Graflok backs can accept acecessories for either the Graphic or the Graflok back.
The Graflok back has two retention systems. Each system is a quick-release type. One system retains the focusing screen and hood assembly and the other system retains accessories such as roll film backs.
- The focusing screen and hood assembly has a pair spring-loaded arms that engage a matching pair of hooks cast into the Graflok back. Pushing in on the arms will disengage them. The focusing screen and hood assembly can then be slid slightly to the right in order to remove it from the back.
- A pair of sliding metal plates cross the back, one over the negative opening and one below. These plates engage matching slots on the removable roll film backs.
|Graflex Century Graphic and roll film back|
image by Voxphoto (Image rights)
Cut film holders are retained under the Graflok focusing screen and hood assembly in the same manner as with the Graphic backs. Cut film holders are interchangable between Graphic and Graflok backs.
The film folders and focusing screen and hood assembly alike are retained by a dual plate or strip system similar to that used to retain roll film backs on the Graflok back. The focusing screen and hood assembly is not spring loaded and must be removed in order to install any film holder. Graflex film holders are not interchangeable with Graflok or Graphic film holders. Graflex backs were available as an option, but are not frequently seen on Graflex press cameras.
Graflex press cameras have no rear movements.
|Century Speed Graphic|
image by Mike Novak (Image rights)
|Model||Rise||Shift||Tilt (deg.)||Swing (deg.)||Bed drop (deg.)|
(Crown and Speed) 4x5
(Crown and Speed) 2x3
|Super and Super Speed||1.125||0.5||+/-15||+/-25||15|
Note: "y" means the movement is possible but exact figure is not available. Please help to complete this table.
A sports finder was standard equipment on all Graflex press cameras. Parallax adjustment is on the hoop or the eyepiece, depending on model.
- "Automatically adjusts for most different lenses, because the hoop of the finder is the same size as the image being formed, and is at about the same distance from your eye as it is from the film, except for telephoto lenses, which are not placed their focal length away from the image plane." -www.graflex.org
Optical "Telescope" Viewfinder
This was an optional finder, also known as a "tubular" finder. The finder eyepiece rotates to provide a rough parallax correction.
This finder uses "masks" inserted behind the finder objective lens to present the "correct" field of view for different lens/format combinations. This was an approximation only, though. Note for example that the same mask is used for 2¼x2¾ and 2¼x3¼ roll film backs when a 101mm lens is used.
|Anniversary Speed Graphic (1944)|
Note solenoid and "Darth Vader" flashgun
(Used as prop in "Star Wars)
image by yashicasailorboy (Image rights)
|Catalog no.||Focal length (mm)|
Source: Rapid-Vance 120 Roll Film Holder Guidebook (1967)
Various models of the Speed Graphic had front-shutter solenoids available as an option. This is a small electromagnetic device that pulls on an internal piston to directly trigger the front shutter. This would be connected to a "solenoid" port on various flashguns, such that pressing a trigger on the flashgun would fire the shutter and/or fire the flash. This allowed non-synchronized front shutters to be used with a flash, as the solenoid is adjustable. The firing of the shutter can thus be timed to coincide with the firing of the flash. This is an early but reliable method of flash sync.
|Crown Graphic 4x5 with solenoid|
image by Geoff Harrisson (Image rights)
The Pacemaker Speed Graphic had dipole flash synchronization on its default front shutter (for any speed) and on its back shutter (for using flat-peak bulbs at speeds of 1/120th or below.) It was also commonly equipped with the solenoid.
On cameras from the Pacemaker line (and to some extent the later Graphics as well), there were cumbersome but usable provisions for extra-wide lenses (which would normally get the edge of the folding bed in frame): the bed can be dropped by 20 degrees by pressing on the struts and pulling it further down, normally giving a few degrees of tilt, but in combination with the (equal and opposite) front-standard tilt, the front and back become parallel again. The front rise can then be used to bring the lens axis back in line with the center of the film. As the focusing rack is now angled, the camera must be focused with the ground glass, and as the vertical position of the front standard changes when focusing, the rise must be adjusted after focusing.
Side-to-side shift is well hidden on the Pacemakers. The rack clamp (ring lever under front standard) must be loosened, and a spring-steel catch under this lever must be held down. The standard-carrier is now loose to move from side to side, but the struts will restrict the range of movement in most circumstances except extreme closeup.
On almost all Graphics (with the exception being the Supers) the lensboard is mounted in the standard by a lip, which mates with two lips on the standard, and two diagonally-sliding clips, on the standard, which move out of the way to allow the entire lensboard to be removed. The lensboards are generally not interchangeable from model to model and between sizes of the same model, with exceptions. There was a practice among some photographers of mounting the lensboard upside-down, allowing easy access to the aperture lever. This sacrifices the use of the internal cable release on the Pacemaker et al, and makes cocking and firing the front shutter unwieldy, so it was mostly used by photographers who preferred the rear shutter.
The camera was often sold with a leather strap to allow the photographer a firm grip with his or her left hand. Many flashguns clip directly on to the lugs for this strap, or alternatively to a plate attacked to the housing of the side-mounted rangefinder, where applicable; if the photographer wished to use his or her right hand to operate the flash.
- Graflex Rapid-Vance 120 Roll Film Holder Guidebook
|Anniversary Speed Graphic (1944)|
image by yashicasailorboy (Image rights)
- Speed Graphic Nude: What's underneath their clothes?
- Super Graphic: Best Buy in 4x5 Field Cameras
- Super Graphic Conversion to Technical Camera
- Enter the World of Graflex all about Graflex Press Cameras
- Graflex instruction manuals, English at Butkus.org
- Graflex Speed Graphic at Classic Cameras by RaúlM.